Site Language

Translate

Danish Dutch English French German

CashBack Реальный возврат при покупках в интернете

CashBack Все честно и без обмана

Arduino Nano

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech.

ArduinoNano
ArduinoNano

Schematic and Design

Arduino Nano 3.0 (ATmega328): schematic, Eagle files.

Arduino Nano 2.3 (ATmega168): manual (pdf), Eagle files. Note: since the free version of Eagle does not handle more than 2 layers, and this version of the Nano is 4 layers, it is published here unrouted, so users can open and use it in the free version of Eagle.

Specifications:

Microcontroller

Atmel ATmega168 or ATmega328

Operating Voltage (logic level)

5 V

Input Voltage (recommended)

7-12 V

Input Voltage (limits)

6-20 V

Digital I/O Pins

14 (of which 6 provide PWM output)

Analog Input Pins

8

DC Current per I/O Pin

40 mA

Flash Memory

16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader

SRAM

1 KB (ATmega168) or 2 KB (ATmega328)

EEPROM

512 bytes (ATmega168) or 1 KB (ATmega328)

Clock Speed

16 MHz

Dimensions

0.73" x 1.70"

Length

45 mm

Width

18 mm

Weigth

5 g

Power:

The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.

Memory

The ATmega168 has 16 KB of flash memory for storing code (of which 2 KB is used for the bootloader); the ATmega328 has 32 KB, (also with 2 KB used for the bootloader). The ATmega168 has 1 KB of SRAM and 512 bytes of EEPROM (which can be read and written with the EEPROM library); the ATmega328 has 2 KB of SRAM and 1 KB of EEPROM.

Input and Output

Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead()They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

  • Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the FTDI USB-to-TTL Serial chip.
  • External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
  • PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function.
  • SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language.
  • LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.I2C: A4 (SDA) and A5 (SCL). Support I2C (TWI) communication using the Wire library (documentation on the Wiring website).

The Nano has 8 analog inputs, each of which provide 10 bits of resolution (i.e. 1024 different values). By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using the analogReference()Analog pins 6 and 7 cannot be used as digital pins. Additionally, some pins have specialized functionality:

There are a couple of other pins on the board:

  • AREF. Reference voltage for the analog inputs. Used with analogReference().
  • Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

See also the mapping between Arduino pins and ATmega168 ports.

Communication

The Arduino Nano has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega168 and ATmega328 provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1).

A SoftwareSerial library allows for serial communication on any of the Nano's digital pins.

The ATmega168 and ATmega328 also support I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus; see the documentation for details. To use the SPI communication, please see the ATmega168 or ATmega328 datasheet.

Programming

The Arduino Nano can be programmed with the Arduino software (Select "Arduino Diecimila, Duemilanove, or Nano w/ ATmega168" or "Arduino Duemilanove or Nano w/ ATmega328" from the Tools > Board menu (according to the microcontroller on your board). For details, see the reference and tutorials.

The ATmega168 or ATmega328 on the Arduino Nano comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files).

You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details.

Automatic (Software) Reset

Rather then requiring a physical press of the reset button before an upload, the Arduino Nano is designed in a way that allows it to be reset by software running on a connected computer. One of the hardware flow control lines (DTR) of the FT232RL is connected to the reset line of the ATmega168 or ATmega328 via a 100 nanofarad capacitor. When this line is asserted (taken low), the reset line drops long enough to reset the chip. The Arduino software uses this capability to allow you to upload code by simply pressing the upload button in the Arduino environment. This means that the bootloader can have a shorter timeout, as the lowering of DTR can be well-coordinated with the start of the upload.

This setup has other implications. When the Nano is connected to either a computer running Mac OS X or Linux, it resets each time a connection is made to it from software (via USB). For the following half-second or so, the bootloader is running on the Nano. While it is programmed to ignore malformed data (i.e. anything besides an upload of new code), it will intercept the first few bytes of data sent to the board after a connection is opened. If a sketch running on the board receives one-time configuration or other data when it first starts, make sure that the software with which it communicates waits a second after opening the connection and before sending this data.

Плата расширения L293D, ИК-датчик VS1838B, TFT LCD, Модем M590E GSM GPRS, "монитор TFT LCD, датчик движения HC-SR501, ИК-пульт дистанционного управления, Радиомодуль NRF24L01, SD Card Module, Звуковой модуль, 5-axis stepper motor driver, Шаговый двигатель, Модем M590E GSM GPRS, 5-axis stepper motor driver, Часы реального времени DS 3231/DS 1307, терморегулятор W1209 DC, Релейный модуль, датчик движения HC-SR501, Модуль Wi-Fi ESP8266-12E, датчик движения HC-SR501, Передатчик и приемник в диапазоне RF 433 Mhz, Блок питания, L293D, Микросхема контроллера коллекторного электродвигателя, ИК-пульт дистанционного управления, Датчики контроля температуры, Радиомодуль NRF24L01, OKI 120A2, Rotary Encoder, SD Card Module, Беспроводной пульт дистанционного управления, Микросхема контроллера коллекторного электродвигателя, Модуль Bluetooth HC-06,, Модем M590E GSM GPRS, Часы реального времени DS 3231/DS 1307, Mini 360 на схеме LM2596, MP3-TF-16P, L293D, Модуль LCD монитора, Инфракрасные датчики расстояния, Часы реального времени, USB Host Shield, HC-SR501, Cветочувствительный датчик сопротивления, блок питания Mini 360 на схеме LM2596, ЖК-дисплей TFT дисплей, Контроллер L298N, HC-SR501, Модуль MP3 Player WTV020, GSM GPRS, Сервоприводы, Модем M590E GSM GPRS, Часы реального времени DS 3231/DS 1307, Модуль Wi-Fi ESP8266-12E, Инфракрасные датчики расстояния, Card Module, Ультразвуковые дальномеры HC-SR04, Блок питания, Карта памяти SD, Mini 360, Ethernet shield, L293D, блок питания Mini 360 на схеме LM2596, Радиомодуль, датчик температуры DS18B20, ИК-пульт дистанционного управления, USB конвертер UART, ИК-пульт, Антена для модуля WiFi, Ethernet shield, Модуль блока питания XL6009, Микросхема контроллера коллекторного электродвигателя, Модуль качества воздуха MQ-135, Микросхема контроллера коллекторного электродвигателя, ИК-пульт дистанционного управления, SD Card Module, Радиомодуль NRF24L01, двигатель OKI, 5-axis stepper motor driver, L293D, TB6560, Драйвер шагового двигателя TB6600, Шаговый двигатель, Модуль камеры, Блок питания, L293D, блок питания Mini 360 на схеме LM2596, 5axis mach3 interface, Карта памяти SD, Ethernet shield, Контроллер L298N, датчик движения HC-SR501, Модуль Wi-Fi ESP8266-12E, Модуль LCD монитора LCD1602, Шаговый двигатель OKI 120A2, Шаговый двигатель, Шаговый двигатель.

All Vintage Vinyl Records VinylSU.xyz

1.png2.png3.png4.png5.png

РУБИКОН Группа «Мозаика», ИЕРОГЛИФ ГРУППА «ПИКНИК», В ПОЛЁТ ГРУППА «ТЯЖЕЛЫЙ ДЕНЬ», Группа «Алиса», Бенни Гудмен, Равноденствие ГРУППА «АКВАРИУМ», Элтон Джон Твоя песня, Демон Группа «Август», Deep Purple – The House Of Blue Light, «Лед Зеппелин» Led Zeppelin, «Акцепт», Doors, «Металлика», АНСАМБЛЬ „UB 40", группа «Зоопарк», рок-группа «ЗОДИАК», «Браво», «Кино», Rolling Stones «Роллинг стоунз», РОК-ГРУППА «МАШИНА ВРЕМЕНИ»,«Кокто твинз», Группа «ДИАЛОГ», Bill Evans, Джимми Лансфорд, Флетчера Хендерсона, Дюк Эллингтон, Каунт Бейси, АНСАМБЛЬ "THE MOODY BLUES", Элвис Пресли, "Юнона" и "Авось" , Дж. Верди Реквием G.Verdi Requiem Mass, Элтон Джон, Реджинальд Кеннет Дуайт, АББА, ABBA, “Deep Purple”, «ЧЕЛОВЕК С БУЛЬВАРА КАПУЦИНОВ», “Rolling Stone”, Instrumrutal rock group Zodiac,‘‘Long Tall Ernie and The Shakers”, “The Beatles”, "Tom Fcgerty and The Blue Velvets", "Creedruce Clearwater Revival","Greru River" "Bayou Country", "Willy and The Poorboys", Varnishing Day Songs on Ilya Reznik's lirics , Leo Sayer ЛЕО СЕЙЕР, Boney M,"Waiting For The Sun", Doors «ДОРЗ», "Piper At The Gates Of Dawn", Led Zeppelin ? «ЛЕД ЗЕППЕЛИН», Rolling Stones , "Юнона" и "Авось" Опера Либретто, «РОЛЛИНГ СТОУНЗ», Modern talking,"Aftermath", «ДОМ ГОЛУБОГО СВЕТА», "Out Of Our Heads", Ricchi E Poveri, PINK FLOYD «Пинк Флойд», Vladimir Kuzmin, ПОЛ МАККАРТНИ Paul McCartney, «TWruTY FLIGHT ROCK», Creedruce Clearvater revival Traveling band,«LAWDY. MISS CLAWDY», «BRING IT ON HOME TO ME», Light My Fire,«DON'T GET AROUND MUCH ANY MORE», МУЗЫКАЛЬНЫЙ ТЕЛЕТАЙП-3,«I'М GONNA BE A WHEEL SOME DAY», МОДЕРН ТОКИНГ,«AINT THAT A SHAME», «THAT'S ALL RIGHT (МАМА)», АНСАМБЛЬ UB 40, «JUST BECAUSE», МИГЕЛЬ РАМОС, «SUMMERTIME», "АНСАМБЛЬ "THE MOODY BLUES", «CRACKIN UP», ТНЕ СОММОDORES, «MIDNIGHT SPECIAL», АННА ГEРМАН, Deep Purple «ДИП ПЁРПЛ», „Deep Purple in Rock", Андрей Миронов, Олег Табаков, Михаил Боярский, Николай Караченцов, Альберт Филозов, Олег Анофриев, Игорь Кваша, Леонид Ярмольник, ИЛЬЯ РЕЗНИК , Резанов Николай Петрович, ВЛАДИМИР ВЫСОЦКИЙ, Роджер Уотерс, АЛЕКСАНДР РОЗЕНБАУМ, Ричард Райт и Ник Мэйсон, ВЛАДИМИР КУЗЬМИН, Элвис Аарон Пресли, Leo Sayer, АДРИАНО ЧЕЛЕНТАНО, Билл Эванс, Клаудия Мори....

и это еще не конец.

С уваженим Dron!